- #Hp smart array p410i controller support hdd 500gb install
- #Hp smart array p410i controller support hdd 500gb drivers
- #Hp smart array p410i controller support hdd 500gb full
for fast backups, or large databases) is quite expensive in SSD (even more with NVMe), we still need hard disks, but not supporting SATA III mode on modern drives is unfortunate.
#Hp smart array p410i controller support hdd 500gb full
Note that you tested your SATA drives with this SAS controler (meaning you get only half the bandwidth for SATA, compared to full SAS support which operates in full-duplex on separate channels for reads and writes, but allows you to use the port multipler in SATA mode, by using the two channels in simplex mode to connect two SATA devices per SAS port).Īnyway, you still don't reach the SATA III speed (6Gbps) of most existing drives.Īs large volume storage (e.g. Surface Analysis Inconsistency Notification: Disabled
![hp smart array p410i controller support hdd 500gb hp smart array p410i controller support hdd 500gb](https://i.ebayimg.com/thumbs/images/g/Ns8AAOSws8Fgdde8/s-l300.jpg)
Here are some details about the P410i itself from the same show config detail: Smart Array P410i in Slot 0 (Embedded) As expected for the lower rotational speed, the WD Reds operate more slowly. Shingled Magnetic Recording Support: NoneĪnd here's the WD red physical drive details: physicaldrive 1I:1:4Įven with the physical block size change, it operates fine for bulk storage. The physical drive details are also similar- here's the detail from an HP drive: physicaldrive 1I:1:2 Physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA HDD, 1 TB, OK)Ībout the only difference is "OS Status: LOCKED" and the mount point info. Physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA HDD, 1 TB, OK) WD Red SATA drive logical drive details: Logical Drive: 2 Physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA HDD, 1 TB, OK) Physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA HDD, 1 TB, OK) Mount Points: /boot 1024 MB Partition Number 1 HP 1TB SATA drive logical drive details: Logical Drive: 1 Here is some example output from ssacli ctrl all show config detail with some details obscured to show how they compare to HP branded SATA drives. They work fine, but as expected are a bit slower than 7200 RPM SATA drives. I have tested WD Reds (WDC WD10JFCX-68N) in some D元60 G6 servers without any unexpected issues. I'll use anything that will keep the fan noise whisper quiet :)ĪNSWER: Dont fight the fed, for the cost differential just get the vendor hardware. (but I think everything was flashed up to date before I got them).ĮDIT2: Probably worth mentioning that getting the hitachis to work would be nice, but isn't vital. I haven't checked the P410i yet, will do that when I get back to work. nothing :/ĮDIT: I should mention I've checked the ILO and the motherboard firmware is up to date. I did look for some sort of official compatibility list, but given the age of my gear. Not just spinning up and booting, but also being happily monitored by the system (with or without) needing drivers. (just because i chanced on a drive that works).Ĭan anyone with experience with the P410i and SATA drives share their experience - which models are -known- to work. Now, just having a single configuration that works, I have a way forward, however buying a whole bunch of small old model Samsung SSD doesn't seem the -ideal- solution.
#Hp smart array p410i controller support hdd 500gb install
I can happy install the latest *nix version of my preference without concerning myself with HP agents to manage the fan speed.
#Hp smart array p410i controller support hdd 500gb drivers
Operating system and drivers making no difference. Instant quiet - fans running blissfully at 15%, barely more noise than my desktop.
![hp smart array p410i controller support hdd 500gb hp smart array p410i controller support hdd 500gb](https://www.itinstock.com/ekmps/shops/itinstock/images/hp-598256-001-smart-array-p410i-1gb-fbwc-sas-controller-battery-bridge-connect-54930-p.jpg)
I took out the hitachi's and plugged in a Samsung evo 256GB. We have a small server room, but the thunderous noise from a bunch of these would have disturbed the office. Taking out all but one of the drives doesn't change the situationĪt this point, after googling numerous articles about HP fan noise, I was getting worried. The hitachi's can't be monitored by the P410i (lacking compatible SMART support?) and so ILO reports a drive bay heat problem and the fans kick on to 80% regardless of OS / drivers Now I think I need the help of someone who actually knows hardware. I'm not an experienced hardware guy FYI, but I've spent a week of late nights googling and experimenting to get to here. Our requirements are cheap, reliable, and far third, lots of storage space. They each came with 4 x 2.5" hitachi 1TB 7200 SATA drives, 6 core CPU, and 72 GB RAM. We picked up a number of HP D元60 G6 at an enormously good price (as far as we could tell). (we normally use cloud).īeing a small company, we have scanty budget, but also flexibility. My company needed some internal, reliable servers for internal data.